Deutsch
Español
Français
There are no more items in your cart
Zenit AZ 38" Longboard Complete
€447.25
€389.95
Tax included
Pack description
Longboard for LDP and Carving/cruising Zenit AZ 38" x 9.5". This longboard with a lowered wedged profile features a low ground clearance for an easier and less strenuous foot push. The nose has a 10° angle while the tail has a 13° dewedge. These angles serve to facilitate pumping and improve carving capabilities. The kicktail at the back is a valuable aid for overcoming obstacles like speed bumps or sidewalks. The Zenit AZ is made up of a maple and triaxial fiberglass sandwich which gives it a medium flex absorbing all road irregularities. Wheelbase 28.5"-29". Handmade in Montreal, Canada. Complete board equipped with trucks Paris V3 165mm 50°, Bearings Nut Steel Balls Built-in, and wheels Zenit LDP 90mm 78A.
Pack Informations
Longboard for LDP and Carving/cruising Zenit AZ 38" x 9.5". This longboard with a lowered wedged profile features a low ground clearance for an easier and less strenuous foot push. The nose has a 10° angle while the tail has a 13° dewedge. These angles serve to facilitate pumping and improve carving capabilities. The kicktail at the back is a valuable aid for overcoming obstacles like speed bumps or sidewalks. The Zenit AZ is made up of a maple and triaxial fiberglass sandwich which gives it a medium flex absorbing all road irregularities. Wheelbase 28.5"-29". Handmade in Montreal, Canada. Complete board equipped with trucks Paris V3 165mm 50°, Bearings Nut Steel Balls Built-in, and wheels Zenit LDP 90mm 78A.
Pack content
Zenit AZ 38" x 9.5" Longboard Deck for LDP and Carving/cruising. This longboard with a lowered profile features a low ground clearance for an easier and less strenuous foot push. The nose has a 10° angle while the tail has a dewedge of 13°. These angles serve to facilitate pumping and improve carving capabilities. The kicktail at the back is a valuable help for overcoming obstacles like speed bumps or sidewalks. The Zenit AZ is made up of a maple and triaxial fiberglass sandwich, giving it a medium flex that absorbs all road irregularities. Wheelbase 28.5"-29". Handcrafted in Montreal, Canada. Grip tape included
Data sheet
- Width
- 9.5"(24,13cm)
- Construction
- Maple & Fiberglass
- Wheelbase
- 28.5", 29"
- Grip tape
- Included
- Disciplines
- Carving, Cruising, LDP
- Kicks
- Single Kick
- Mounting of Trucks
- Top mount
- Lenght
- 38"
Semi-flexible flat riser pads. Riser pads to raise the ground clearance of the skateboard to prevent wheelbite and isolate the deck from trucks to reduce vibration. 6-hole pads, compatible with New School and Old School drillins patterns. Available in 1/8" (3mm), 1/4" (6mm), 3/8" (9mm), & 1/2" (12mm). Sold in pairs
What screw size should I use?
Pads 1/8": 1" to 1.125" screws
Pads 1/4": 1.125" to 1.25" screws
Pads 3/8" and 1/2": 1.5" screws
Data sheet
- Truck Hole Pattern
- Short 4 - 2.125" (New School), Length: 4 -2.5" (Old School)
Paris V3 Hollow Lite 50° 165mm. Versatile Truck for dancing, carving, freestyle, pumptrack, Freeride,... Good balance between agility and stability. Paris is the number 1 manufacturer for longboard trucks, and owes its popularity to its ease in carving as well as its robustness. The Paris 165mm are suitable for longboards less than 9" wide, and/or for riders looking for tighter lines and enhanced grip. Hollow axle and kingpin allow 7% wight saving to compare with standard Paris V3. Equipped with Divine Standard longboard height bushings (Barrel 90A side deck / Cone 90A road side). 96A polyurethane pivot cup facilitating pivot. Deep bushing seat for more precision. Truck sold individually
Data sheet
- Width
- 165mm
- Construction
- Cast Aluminium, Hollow Kingpin, Hollow Axle
- Disciplines
- Pumptrack, Carving, Cruising, Dancing, LDP
- Kingpin Angle
- 50°
- Geometry
- Inverted
- Bushings Heights & Shapes
- Barrel, Cone, Longboard Standard Height 0.6"
- Trucks Axles Diameter
- 8mm(Standard)
- Truck Hole Pattern
- Short 4 - 2.125" (New School), Length: 4 -2.5" (Old School)
The Nut Classic Steel Balls Built-In bearings with integrated spacers and speed rings are specifically designed for longboarding. Their precise manufacturing ensures a perfect fit in the wheels and along the axles, providing optimal alignment and a smooth ride. Equipped with 7 steel balls lubricated with low-viscosity oil and a finish of quality equivalent to or higher than Abec-9, the Nut Steel Balls Built-In deliver exceptional speed performance, making them ideal for downhill, pump track, LDP, as well as cruising and dancing. Thanks to their two removable rubber shields, the bearings stay cleaner for longer. This set includes 8 bearings, compatible with most skateboard and longboard wheels (not compatible with roller skates).
Data sheet
- Trucks Axles Diameter
- 8mm(Standard)
- Balls material
- Steel
- Built-In Spacers?
- With Built-In Spacers
With the Zenit LDP (Long Distance Pumping) 90mm wheels maximize the distance covered with each push, and always ride further and with less effort. With their large diameter, the Zenit LDP maintain their momentum longer, and easily overcome all road deformations. The 78A high rebound rubber ensures comfort and speed. Wheel width of 50mm for 45mm of rolling band. Center-set core. Set of 4 wheels
Data sheet
- Width
- 50mm
- Contact Patch
- 45mm
- Core Placement
- Center-set
- Wheel surface
- Smooth
- Diameter
- 90mm
- Durometer(s)
- 78A
- Weight
- 1.08Kg/ set of 4 wheels
- Disciplines
- LDP, E-Skateboard
- Grip level
- 4/5