Deutsch
Español
Français
There are no more items in your cart
Pantheon Mitch Thompson 32" Longboard Complete
€406.25
€384.95
Tax included
Pack description
Downhill longboard Pantheon Pro model Mitch Thompson. Compact design in line with modern standards. The 8-ply maple construction coupled with 2-ply tri-axial fibreglass provides rigidity and absence of torsion, two essential qualities for maintaining stability at high speeds. The medium concave transforms into a W at the rear to create cushioning points without getting in the way when pushing off with the foot. At the front, the foot is positioned just above the truck for maximum responsiveness. Dimensions 32.125" x 9" (8.45" front, 8.59" rear). Fully equipped for downhill and fast freeride.
Pack Informations
Downhill longboard Pantheon Pro model Mitch Thompson. Compact design in line with modern standards. The 8-ply maple construction coupled with 2-ply tri-axial fibreglass provides rigidity and absence of torsion, two essential qualities for maintaining stability at high speeds. The medium concave transforms into a W at the rear to create cushioning points without getting in the way when pushing off with the foot. At the front, the foot is positioned just above the truck for maximum responsiveness. Dimensions 32.125" x 9" (8.45" front, 8.59" rear). Fully equipped for downhill and fast freeride.
Pack content
Pantheon Pro Model Mitch Thompson Downhill Skateboard Deck. A compact design that meets the demands of modern race boards and setups with narrow trucks. The 8-ply maple construction combined with 2 layers of tri-axial fiberglass provides stiffness and torsion resistance—two essential qualities for maintaining stability at high speeds. The medium concave transitions into a W-concave at the rear, creating secure foot placement points without hindering foot pushing. At the front, the foot is positioned directly above the truck for maximum responsiveness. Dimensions: 32.125" x 9" (8.45" at the front, 8.59" at the rear).
Recommended Setup
-
For freeride: 150mm trucks (e.g., Paris V3 150mm in 50° and 43° or Bear Grizzly Gen6 155mm 50°/40°) with narrow freeride wheels (e.g., Powell Peralta Snakes 69mm)
-
For racing: 130mm trucks (e.g., Zealous Downhill Slalom V2 133–146) and wide wheels (e.g., Venom Magnum, 88 Wheels Mitch Thompson, Seismic Delta)
Data sheet
- Width
- 9"(22,86cm)
- Construction
- 8-Ply Maple + Fiberglass
- Wheelbase
- 20.125", 22.625"
- Griptape
- Not Included
- Flex
- No Flex
- Disciplines
- Downhill, Freeride
- Kicks
- No Kick
- Mounting of Trucks
- Top mount
- Lenght
- 32.125"
Jessup Roam Rough griptape for longboards. 11" width x 40" lenght. Jessup is a skateboard griptape leader for years. Grip is fexy, grippy, and easy to instal. When buying deck and griptape in the same time, we can stick the grip on the deck for you and for free. Just ask us on your order comment.
The Nut Classic Steel Balls Built-In bearings with integrated spacers and speed rings are specifically designed for longboarding. Their precise manufacturing ensures a perfect fit in the wheels and along the axles, providing optimal alignment and a smooth ride. Equipped with 7 steel balls lubricated with low-viscosity oil and a finish of quality equivalent to or higher than Abec-9, the Nut Steel Balls Built-In deliver exceptional speed performance, making them ideal for downhill, pump track, LDP, as well as cruising and dancing. Thanks to their two removable rubber shields, the bearings stay cleaner for longer. This set includes 8 bearings, compatible with most skateboard and longboard wheels (not compatible with roller skates).
Data sheet
- Trucks Axles Diameter
- 8mm(Standard)
- Balls material
- Steel
- Built-In Spacers?
- With Built-In Spacers
Semi-flexible flat riser pads. Riser pads to raise the ground clearance of the skateboard to prevent wheelbite and isolate the deck from trucks to reduce vibration. 6-hole pads, compatible with New School and Old School drillins patterns. Available in 1/8" (3mm), 1/4" (6mm), 3/8" (9mm), & 1/2" (12mm). Sold in pairs
What screw size should I use?
Pads 1/8": 1" to 1.125" screws
Pads 1/4": 1.125" to 1.25" screws
Pads 3/8" and 1/2": 1.5" screws
Data sheet
- Truck Hole Pattern
- Short 4 - 2.125" (New School), Length: 4 -2.5" (Old School)
Redesigned from the ground up and incorporating technology perfected in the high end DH and Freeride trucks, Gen 6 Grizzlies are the best performing cast trucks on the market today. Game changing strength and highly refined steering geometry are just the tip of the iceberg, Gen 6 Grizzlies 50° 130mm are Downhill/f Freeride oriented trucks. They would fit best on narrow decks. 130mm are more turny and have more traction to compare with 180mm trucks. Hollow Kingpin. Set with 83A Step Barrel / Cone Bushings. Sold as a single truck
Data sheet
- Width
- 130mm
- Construction
- Cast Aluminium, Hollow Kingpin
- Disciplines
- Freeride, Downhill
- Kingpin Angle
- 50°
- Geometry
- Inverted
- Trucks Axles Diameter
- 8mm(Standard)
Redesigned from the ground up and incorporating technology perfected in the high end DH and Freeride trucks, Gen 6 Grizzlies are the best performing cast trucks on the market today. Game changing strength and highly refined steering geometry are just the tip of the iceberg, Gen 6 Grizzlies 30° 130mm are Downhill oriented trucks. They would fit best on narrow decks and be set as a rear truck matching with a Gen5 40° or 50° at the front. 130mm are more turny and have more traction to compare with 180mm trucks. Hollow Kingpin. Set with 95A Step Barrel / Cone Bushings. Sold as a single truck
Data sheet
- Width
- 130mm
- Construction
- Cast Aluminium, Hollow Kingpin
- Disciplines
- Downhill
- Kingpin Angle
- 30°
- Geometry
- Inverted
- Trucks Axles Diameter
- 8mm(Standard)
Data sheet
- Width
- 65mm, 65mm
- Contact Patch
- 65mm, 65mm
- Core Placement
- Center-set
- Lip profile
- Square Lip
- Wheel surface
- Smooth
- Diameter
- 76mm
- Durometer(s)
- 76A
- Disciplines
- Fast Freeride, Downhill
- Gap width between bearing seats
- 10mm(Skateboard/Longboard standard)
- Grip level
- 5/5